Enter your keyword

CEL-FI GO Telstra Repeater Kit – Urban Outdoor Coverage

$1,110.00$1,150.00

The CEL-FI GO Repeater for the Telstra network is a convenient way to boost and distribute a 3G/4G mobile signal within your vehicle, home, office or outdoor area.

Quantity:
SKU: SG-KIT-G31-TU-OD Categories: , Tags: ,

CEL-FI GO Repeater Kit designed for Urban Outdoor Coverage

 

Key Features

  • Complete package with an Externally Mounted Donor Antenna, Cabling, CEL-FI GO Repeater & a Wall Mounted Distribution Antenna
  • Full service for up to 20 Telstra mobile phones or modems
  • 4Gx(700MHz) or Next G(850MHz) or 4G(1800MHz) frequency support (manual selection
  • Suitable for Telstra, Boost, and Aldi Mobile networks
  • Currently Australia’s only legal mobile phone repeater system
  • Custom terminated COL7195 & super low loss extendible cabling.

 

Usage

  • The CEL-FI GO Repeater for the Telstra network is a convenient solution for those experiencing poor phone coverage within the house or office
  • Installing this device in your home can improve the reliability of phone calls, text messages, and increase 3G or 4G or 4GX services
  • This is a complete repeater system designed to provide indoor or outdoor coverage
  • The wideband collinear whip antenna is ideal for urban areas where there is signal available outdoors but it is poor indoors, typically there are a few towers within 10km from your location
  • The COL7195 antenna is connected to the repeater via a run of LCU400 cable with an SMA fitting, which allows the cable to directly connect to the CEL-FI GO’s input connector – from there a smaller grade of LCU195 Cable is connected to the CEL-FI GO’s output which is run to the location where you wish to install the ceiling mounted antenna
  • The repeater provides enough boost to create a 60m area of coverage within normal home or office environments – up to an impressive 100m area in open areas such as supermarkets or farms, as reported by our customers
  • Like all wireless systems, the coverage area is reduced by the signal travelling through thick walls or floors, so the actual coverage area will vary depending on your unique situation
  • The design of this Repeater allows for greater flexibility and we can split the output signal across multiple antennas and even daisy chain the set up down to another location, please don’t hesitate to contact one of our sales staff to discuss the potential options further.
  • It’s important to note that this repeater unit is designed to provide 3G or 4G/x services to mobile devices, it cannot produce both networks concurrently.

 

Single Service Booster Only!

  • This repeater unit is designed to provide 3G or 4G/x services to mobile devices, it cannot produce both networks concurrently.

 

Installation

  • The LPDA Antenna is connected to the repeater via a run of LCU400 cable with an SMA fitting, which allows the cable to directly connect to the CEL-FI GO’s input connector – from there, a smaller grade of LCU195 cable is connected to the CEL-FI GO’s output, which is run to the location where you want to install the ceiling mounted antenna.

 

Similar kits

  • We also provide similar kits for hilly, regional and remote areas experiencing poor coverage.

 

Performance on 4G/4GX Internet

  • To provide the best possible and fastest Internet connection, a proper MIMO external antenna should be connected into a dedicated 3G/4G modem
  • Typical speeds through the repeater unit are around 25-30% of a dedicated modem.

 

Why is it legal?

  • Many mobile service providers do not support the use of personal repeaters on their network. This is due to the interference they can cause when connected to the network, or when they are setup incorrectly
  • The CEL-FI system is the only personal repeater that is widely approved by carriers in Australia
  • The CEL-FI GO is different to a standard repeater, as it is designed to provide maximum coverage, be network friendly and easily installed by the end user, it does this by:
    • continuously monitoring power levels of the cell tower it is connected to and constantly adjusting its output power to suit
    • only amplifying and disbursing a particular carrier’s mobile signal, operating within a set frequency band
    • giving the service provider the ability to shut down the repeater remotely if needed, using a signal from the base station
    • not interfering with the carrier’s network or other users on the network
    • having a unique installation process to eliminate feedback into the mobile network.

Weight 8 kg
Dimensions 130 × 45 × 25 cm
Choose your length of Cable from the Antenna to the Repeater

10m, 15m, 20m, 25m, 30m

Choose your length of Cable from Repeater to the Ceiling Antenna

1.5m, 3m, 5m, 10m

Reviews

There are no reviews yet.

Be the first to review “CEL-FI GO Telstra Repeater Kit – Urban Outdoor Coverage”

Your email address will not be published. Required fields are marked *